sip messagenet on brekeke

miami71it · Post by **miami71it** » Thu Jan 05, 2023 8:07 am

1. Brekeke Product Name and Version:
last version

2. Java version:
last

3. OS type and the version:
win 10

4. UA (phone), gateway or other hardware/software involved:

5. Your problem:

hello everyone, I have a sip line with messagenet manager, and a Brekeke PBX latest version
how can i configure the incoming/outgoing sip line on brekeke? I've never done this until now I've used audiocodes with analog lines
thank you

Harold · Post by **Harold** » Thu Jan 05, 2023 2:43 pm

If the Messagenet manager can send SIP-REGISTER, add the SIP user in the Brekeke PBX.

If you want to use the messagenet manager as a SIP trunk, configure Brekeke PBX's ARS to connect to the Messagenet manager.
https://docs.brekeke.com/pbx/ars-tutorials-samples

miami71it · Post by **miami71it** » Thu Jan 12, 2023 7:03 am

hi thanks for the answer
yes I would like to configure it as a trunk, I have already configured it with 3CX and it was very simple but with brekeke it is more complex the data available to me are:

Your new telephone number is: +39 1234567 (invented number for example)

URI (SIP Client Identifier) 5**********
Password **********
SIP Server sip.messagenet.it:5061

at this point I have to enter these data in ARS, but I didn't register, I did this

Register URI: sip:sip.messagenet.it:5061 (I also tried removing 5061)

Proxy Address: sip.messagenet.it:5061 (I also tried removing 5061)

User: 5**********
Password: *********

but it doesn't register
what am I doing wrong?

miami71it · Post by **miami71it** » Thu Jan 12, 2023 7:37 am

sorry in Register URI I wrote wrong the correct wording is: 5**********@sip.messagenet.it:5061 (I also tried removing 5061)

Brett · Post by **Brett** » Fri Jan 13, 2023 2:50 pm

Hi,

It looks your Register URI is wong.

I think it should be like,
sip:5xxxxxx@sip.messagenet.it:5061

Thank you

miami71it · Post by **miami71it** » Mon Jan 16, 2023 1:42 am

I tried in every way, even as you suggest, but the answer is always this:
Register failed (403 SIP/2.0 403 Forbidden) - sip:5***********@sip.messagenet.it:5061

the credentials are correct, on a 3CX PBX it works perfectly

Brett · Post by **Brett** » Thu Jan 19, 2023 3:43 pm

Hi,
Please check the following points.

- On the server where brekeke is running, the domain "sip.messagenet.it" can be resolved properly.

-If the node "sip.messagenet.it" is located on public, you may need to set public address at [SIP SERVER] > [Configuration] > [System] >[Network].

miami71it · Post by **miami71it** » Fri Jan 20, 2023 7:09 am

from the PC where brekeke is installed I ping sip.messagenet.it and replies OK so he sees it.
I don't understand what you mean, I can't set a public IP on the network otherwise the phones will no longer see the switchboard brekeke
but sorry i don't understand, why in 3CX it's so trivial to configure a messagenet trunk with unser and password and in brekeke it must be impossible°? what's different?

miami71it · Post by **miami71it** » Tue Jan 24, 2023 3:13 am

ideas?

Brett · Post by **Brett** » Wed Jan 25, 2023 1:41 am

Hi,

You don't have to set a public IP on the network interface of the server, but at the Webadmin tool > [SIP SERVER] > [Configuration] > [System] > [Network] >[Interface address 1], set your gateway address(public IP) that communicates to sip.messagenet.it.

If your problem still exists, I recommend you ask brekeke tech support.

miami71it · Post by **miami71it** » Tue Jan 31, 2023 10:02 am

hello thanks but on interface 1 I have the switchboard ip, if I change it the phones no longer see the switchboard.
can i use interface 2?